• Print
• .

MK3BOM

+RX Box+

• 4 QTY Sorbathane Male/Female 0519411-50-4 M4, 12.7 mm(H), 50 duro USD 47.95 /4pack
• 8 QTY F-347-8 FAN MOUNT C-8002 ($55.96/200pcs)
• 4 QTY F-344-8012 BLACK FAN MOUNT ($27.98/100pcs)
• 1 QTY DC Fans DC Fan, 80x25mm 12VDC, Vapo, MagLev ($$133.00/25pcs)
• 1 QTY DC Fans 12Vdc 1.3W 16.3CFM DC Axial 60x60x10mm ($121.75/25pcs)
• 1 QTY DC Fans Fan, 120x25mm, 12VDC Vapo, Auto Restart ($$281.75/25pcs)
• 1 QTY FAN GUARD BLND HL MNT BLCK 120MM ($62.20/25pcs)
• 1 QTY FAN GUARD BLND HL MNT BLACK 80MM ($55.54/25pcs)
• ? QTY ROUND HEATPIPE 45W 6X200MM ($749.82/124pcs)
• 1 QTY 1m SCSI Cable CS-VHDCIMX200-001 ($1171.70/40pcs)
• (a)(1 QTY 12-13.5 Volt molex y cable)
• (a) (1 QTY MOLEX PIGTAIL)
• (b) 2 QTY 6 pin molex to crescent connectors (VICOR) (9")
• 1 QTY 6-pin MOLEX DTAQ (1/2 of 24")
• 1 QTY 4-pin LO SPLIT MOLEX (24")
• 1 QTY 8-pin LO RX POWER (26")
• 1 ACTIVE ANTENNA JUMPER for POWER-DISTRIB
• 3 fan cables connectors (24-gauge)
• 1 PAIR EYELETS VICOR to INPUT TERMINAL (9")
• 1 GROUND STRAP CHASSIS to INPUT TERMINAL (21")
• 1 GROUND STRAP CHASSIS to connector plate (6")
• 1 GROUND STRAP DTACQ to CHASSIS (12")
• 2 GROUND STRAP PANEL DOOR To RX Plate (12")
• 1 JUMPER
• 1 QTY UHF COAX CABLE to INPUT TERMINAL (28+8") including pigtail/connector (51/25) need to add pigtail
• 1 QTY UHF elbow
• 9 QTY SMA-N bulkhead
• 1 QTY UHF F-F bulkhead
• 2 ferrite ZCAT2132-1130
• 1 ferrite ZCAT2235-1030
• 1 ferrite ZCAT1325-0530
• 2 ferrite ZCAT1730-0730
• 9 qty 24" RG316 sma male right angle to sma male right angle
• 2 qty 30" RG316 sma male straight to mcx right angle
• 3 qty 9" RG316 mcx right angle to mcx straight male
• 1 qty 6" RG316 mcx right angle to mcx right angle male

FOR 8-Antenna Systems

• LO distribution conversion mounting

+POWER BOX+

• toroid box 749.1202 (25/25)
• traco 300 TIS300-124 (13/25) if 4 channel
• traco 500 TIS500-124-230 (1/?) if 8 channel
• 1 qty 6 amp DC Breakers https://www.altestore.com/store/enclosures-electrical-safety/overcurrent-devices-fuses-breakers/din-rail-circuit-breakers/din-rail-mount-circuit-breakers-p40906/?gclid=EAIaIQobChMIjb27_sjH2QIVBTJpCh0ucA_OEAQYBCABEgJRc_D_BwE#GENBRKDIN-6
• 1 qty 8 amp DC breakers (26/25)
• 1 UHF COAX CABLE to POWER (12+8") including pigtail/connector (51/25) need to add pigtail connector
• 1 QTY NType elbow (25/72) available in LAB
• 1 QTY UHF elbow
• 1 QTY SMA-N F-F bulkhead
• 1 QTY UHF F-F bulkhead
• 1 QTY lightning arrestor http://nextek.com/products/product/ptconfonf15s/
• 1 ferrite ZCAT2132-1130
• 2 ferrite ZCAT1730-0730
• 1 QTY 42" RG316 SMA Male Right Angle to SMA Male Right Angle RF Coaxial Cable
• 1 QTY 12" RG316 SMA Male Right Angle to SMA Male Right Angle RF Coaxial Cable
• 1 QTY 24" RG142 N Male to SMA Male RF Coaxial Cable
• 2 QTY 18" RG316 MCX Male to MCX Male Right Angle RF Cable
• 2 QTY 20" RG316 SMA Male Right Angle to SMA Male Right Angle RF Coaxial Cable
• 1 QTY db9 to 10 pin connector
• 1 QTY 5' 4pin MOLEX

To purchase for assembly of RX (it comes in packs of 100 usually):

All stainless steel & hex heads (it’s actually cheaper in hex). I recommend buying one set of the items listed bellow and to test that everything works together just fine before buying larger quantities.

McMaster:

• https://www.mcmaster.com/#94500A221 ; packs of 100; M3 6mm (RX boards) (QTY required: ~80/RX)
• https://www.mcmaster.com/#94500A222 ; packs of 100; M3 8mm PCB mounting (QTY required: ~25/RX)
• https://www.mcmaster.com/#94500A265 ; packs of 100; M3 16mm Distrib PCB mounting (QTY required: ~10/RX)
• https://www.mcmaster.com/#19155k35/=1b2v7so ; single unit; 1 RFI for 80mm fan (QTY required: 1/RX)
• https://www.mcmaster.com/#5801k8/=1b2vc5k ; packs of 20; Fan rubber mount (QTY required: 12/RX)
• https://www.mcmaster.com/#93395a201/=1b2vd9o ; packs of 100; D-tacq bell mount (QTY required: 4/RX)
• https://www.mcmaster.com/#92871a017/=1b2vpte ; for corners of power input PCB & Vicor PCBs (QTY required: 12/RX)
• https://www.mcmaster.com/#92871A181 ; for vicor power modules themselves (QTY required: 8/RX)
• https://www.mcmaster.com/#94500a266/=1b2vraf ; for bolting power modules onto the heat plate through the standoffs (QTY required: 20/RX)

Digikey:

• QTY 1 https://www.digikey.com/products/en/fans-thermal-management/dc-fans/217?k=&pkeyword=&pv2187=u2.90W&FV=ffec4e10%2Cffec85c2%2Cfffc0103%2C14328b%2C38007e%2Cb897b4%2Cb8b45f%2C30404bf%2C304085e%2Cmu2.90W%7C2187%2Cmu3.10W%7C2187%2Cmu5.10W%7C2187%2Cffe000d9%2Ce80008&mnonly=0&ColumnSort=0&page=1&nstock=1&datasheet=1&photo=1&rohs=1&quantity=0&ptm=0&fid=0&pageSize=25 OR https://www.digikey.com/products/en/fans-thermal-management/dc-fans/217?k=&pkeyword=&pv1026=490&FV=fffc0103%2C38007e%2Cb897b4%2Cb8b45f%2Ce80008%2C30404bf%2C30404d2%2C1f140000%2Cffe000d9%2C14328b&mnonly=0&ColumnSort=0&page=1&nstock=1&datasheet=1&photo=1&rohs=1&quantity=0&ptm=0&fid=0&pageSize=25 ; the difference is the width, need to check compatibility but I think the first is better if it fits.
• QTY 1 https://www.digikey.com/product-detail/en/sunon-fans/MF80251V2-1000U-A99/259-1785-ND/6198723
• QTY 1 https://www.digikey.com/products/en/fans-thermal-management/dc-fans/217?k=&pkeyword=&pv58=12&FV=38007e%2C30404a6%2C30404b1%2C30404b4%2C30404c1%2C30404cc%2C30404d1%2C304056d%2C30406d9%2C30406da%2C30406de%2C30406df%2C30406e0%2C30406f7%2C30406fb%2C30406fc%2C30406fd%2C3040705%2C3040706%2C3040707%2C3040713%2C3040715%2C3040716%2C3040718%2C3040719%2C3040882%2C3040883%2Cffe000d9%2Cb897c6%2Cb8b3ec&mnonly=0&ColumnSort=0&page=1&nstock=1&datasheet=1&rohs=1&quantity=0&ptm=0&fid=0&pageSize=25

Pierre may bring some of the above but there are not enough leftovers for many more enclosures.

However he has enough of these left for all enclosures, already purchased, if he brings them:

• Rondelle/washer inox M8 4 (for spacing on U-channel)
• All M6 & M5s for U-channels plate mounting, and bottom vent closures.
• M5 nuts for the heat-plates and grounding.

Cheers, Mael 52 substitutions on 52 lines